{"product_id":"radial-lx-2-line-level-splitter-new","title":"Radial LX-2 Line-Level Splitter — New","description":"\u003ch2\u003eRadial LX-2 Line-Level Splitter \u0026amp; Attenuator\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003ePassive Line-Level Splitter \u0026amp; Attenuator \u003c\/strong\u003eThe LX-2ô is a passive balanced line-level audio splitter that allows you to easily send an audio signal to two different destinations at once without noise, while also providing the ability to attenuate the signal when needed.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSplit \u0026amp; attenuate audio with ease \u003c\/strong\u003eThe LX-2 performs the dual functions of splitting a line level audio signal and providing level attenuation where necessary. A premium Jensen transformer inside provides exceptional frequency response and phase coherency to ensure that the highest audio quality is maintained, while isolating the two outputs from each other to eliminate hum and buzz from ground loops. For situations where a level adjustment is required, the trim control on the LX-2 allows you to attenuate overly hot signals. This gives you the ability to drive your mic preamps hard to achieve coloration, while trimming the level at the LX-2 to avoid clipping the inputs of your recording interface. This trim control is activated by a recessed ëset \u0026amp; forgetí switch; if attenuation is not needed, simply disengage this switch to prevent accidental and unwanted level adjustments.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSplitting line outputs on stage \u003c\/strong\u003eSend the output of a mic pre or line level device to a recording interface as well as the PA system\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSplit the output of a mic preamp in the studio \u003c\/strong\u003eSend the output of a single preamp to two compressors simultaneously. Use the level trim to push your preamp harder for coloration without distorting the compressor inputs.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eUsing the LX-2 for parallel effects processing\u003c\/strong\u003eSplit the output of a preamp to feed an outboard effects device while also sending a clean signal to your recording interface. Blend the signals together in your DAW for parallel processing.\u003c\/p\u003e\n\u003cp\u003eSplit one audio signal to two destinations simultaneously.\u003c\/p\u003e\n\u003cp\u003eJensenÆ transformer equipped for exceptional audio quality.\u003c\/p\u003e\n\u003cp\u003eEliminates hum and buzz caused by ground loops.\u003c\/p\u003e\n\u003cp\u003eVariable trim control can be engaged for easy level adjustment.\u003c\/p\u003e\n\u003ch3\u003eFeatures:\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eCombo Input: Combination XLR 1\/4\" input.\u003c\/li\u003e\n\u003cli\u003eTrim On: Set and Forget switch activates the trim level control. Signal Passes through at unity gain when the switch is not engaged.\u003c\/li\u003e\n\u003cli\u003eTrim Level: Attenuates the signal at the input of the LX-2.\u003c\/li\u003e\n\u003cli\u003eDirect Thru: Direct output to connect to recording or monitor systems.\u003c\/li\u003e\n\u003cli\u003eLift: Disconnects pin-1 ground at the XLR output.\u003c\/li\u003e\n\u003cli\u003eISO Output: Transformer isolated output eliminates hum and buzz caused by ground loops.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications:\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAudio circuit type: Passive, transformer based\u003c\/li\u003e\n\u003cli\u003eTransformer: Jensen JT-11-FLPCH\u003c\/li\u003e\n\u003cli\u003eNumber of channels: 1 input, 1 iso output, 1 direct output\u003c\/li\u003e\n\u003cli\u003eFrequency response: 20Hz - 20kHz +\/-0.5dB\u003c\/li\u003e\n\u003cli\u003eDynamic range: 140dB\u003c\/li\u003e\n\u003cli\u003eGain: -1.5dBu\u003c\/li\u003e\n\u003cli\u003eTotal harmonic distortion: \u0026lt;0.001% @ 1kHz\u003c\/li\u003e\n\u003cli\u003ePhase Deviation: +0.3? @ 20Hz\u003c\/li\u003e\n\u003cli\u003eInput Impedance: 716 ohms\u003c\/li\u003e\n\u003cli\u003eOutput Impedance: 116 ohms\u003c\/li\u003e\n\u003cli\u003eCommon Mode Rejection Ratio: 94dB @ 60Hz, 83dB @3kHz\u003c\/li\u003e\n\u003cli\u003eNoise: -119dBu\u003c\/li\u003e\n\u003cli\u003eMaximum Input: +21dBu\u003c\/li\u003e\n\u003cli\u003eGround lift, Level Control\u003c\/li\u003e\n\u003cli\u003eInput Connectors: Combo XLR \/ 1\/4\"\u003c\/li\u003e\n\u003cli\u003eOutput Connectors: isolated XLR, direct XLR\u003c\/li\u003e\n\u003cli\u003eConstruction: 14-gauge steel\u003c\/li\u003e\n\u003cli\u003eSize (L x W x D): 84mm x 127mm x 48mm (3.3\" x 5\" x 2\")\u003c\/li\u003e\n\u003cli\u003eWeight: 0.7kg (1.5lbs)\u003c\/li\u003e\n\u003cli\u003eShipping size (L x W x D): 102 x 76 x 165mm (4\" x 3\" x 6.5\")\u003c\/li\u003e\n\u003cli\u003eShipping weight: 0.87 kg (1.92 lbs)\u003c\/li\u003e\n\u003cli\u003ePower: Passive, no power required\u003c\/li\u003e\n\u003cli\u003eConditions: For use in dry locations only between 5?C and 40?C\u003c\/li\u003e\n\u003cli\u003eWarranty: Radial 3-year, transferable\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Radial Engineering","offers":[{"title":"Default Title","offer_id":48198344540244,"sku":"LX2","price":161.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0712\/2757\/2308\/files\/LX2.jpg?v=1794612546","url":"https:\/\/voltrivoo.myshopify.com\/products\/radial-lx-2-line-level-splitter-new","provider":"VOLTRIVOO","version":"1.0","type":"link"}